*****************************************2024.12.10 VX400 V1.7.0********************************************************************** [Supporting Software Version] V-Can V3.8.0 or later NovaLCT V5.6.1 or later [New Features] 1. Supports a decimal output frame rate of 49.98Hz. [Improvements] None [Changes] None [Bug Fixes] 1. Fixed the LCD screen freezing which occurred with low probability under certain operating conditions. 2. Fixed the issue where the layer scaling mode changes from pixel-to-pixel to custom after the device is powered off and then on again. 3. Fixed the rare system freezing that occasionally happened when the device was left running for extended periods without shutting down. 4. Fixed the issue where the OPT port fails to read back receiving card configuration parameters. 5. Fixed the infrequent occurrence of color cast and HDMI source recognitions issues. 6. Fixed the occasional issue where a USB drive cannot be identified with low probability. 7. Supports the EDID compatibility mode to fix the issue where the input source provided by some devices is not displayed completely. [Notes] None *****************************************2024.3.13 VX400 V1.6.0********************************************************************** [Supporting Software Version] V-Can V3.7.1 S1.T3 or later NovaLCT V5.4.8 or later [New Features] 1. Support the importing and exporting of the EDID file. 2. Support display of the device MAC address. 3. Support input source backup. 4. Support the Ethernet port backup test. 5. Support frame rate readback. 6. Support Ethernet port backup status displayed on home screen in fiber converter mode. [Improvements] 1. Optimized the process for importing custom logos. 2. Optimized the central control protocol. [Changes] None [Bug Fixes] 1. Fixed the problem that the device restarts occasionally. 2. Fixed the problem that the last frame is displayed if there is no source, and the screen goes black occasionally when the input source is disconnected. 3. Fixed the problem of interlaced color cast of the SDI source. [Notes] 1. NovaLCT V5.5.1.T2 or later and LCT V5.5.1 or later (main line) are required if you want to use the frame rate readback function. *****************************************2023.10.20 VX400 V1.5.1********************************************************************** [Supporting Software Version] V-Can V3.7.0 S4.T3 or later NovaLCT V5.4.4.6 (VX400) or later [New Features] None [Improvements] None [Changes] None [Bug Fixes] 1. Fixed the problem that the screen is blurred or blacked out after you power off and then power on the device. [Notes] 1. After the device is updated to this version, rolling back to the previous version is not supported. 2. In this version, the ping command is disabled and not supported. *****************************************2023.10.8 VX400 V1.5.0********************************************************************** [Supporting Software Version] V-Can V3.7.0 S4.T3 or later NovaLCT V5.4.4.6 (VX400) or later [New Features] None [Improvements] None [Changes] None [Bug Fixes] 1. Fixed the problem that the Ethernet port occasionally failed to output an image, the MVR window becomes blacked out or blurred and receiving card configuration parameters are read unsuccessfully. 2. Fixed the problem that the garbled characters are displayed on the LCD screen after the cabinet config file is sent via NovaLCT. 3. Fixed the problem that the abnormal image is displayed when the width of the input source exceeds 2048 pixels. [Notes] 1. After the device is updated to this version, rolling back to the previous version is not supported. 2. In this version, the ping command is disabled and not supported. *****************************************2023.5.6 VX400 V1.3.0********************************************************************** [Supporting Software Version] V-Can V3.7.0 S4.T2 or later NovaLCT V5.4.4.6 (VX400) or later [New Features] 1. Support the import of custom logos. [Improvements] None [Changes] None [Bug Fixes] None [Notes] None *****************************************2022.12.9 VX400 V1.0.1********************************************************************** [Supporting Software Version] V-Can V3.7.0.S2.T2 NovaLCT V5.4.4.6 (VX400) [New Features] None [Improvements] None [Changes] None [Bug Fixes] 1. Fixed the problem that the PIP 2 option incorrectly appears when you select the audio output. [Notes] None *****************************************2022.12.9 VX400 V1.0.0********************************************************************** [Supporting Software Version] V-Can V3.7.0.S2.T2 NovaLCT V5.4.4.6 (VX400) [New Features] First release