**************************************2024.01.09 NovaPro UHD Jr V1.9.0.0.STD**************************************** [Supporting Software Version] V-Can V3.7.1.S1.T2 or later NovaLCT V5.4.8.CTM0904 or later [New Features] 1. Support hardware and checkerboard test patterns. 2. Support input source hot backup (OPT source included). 3. Support the Ethernet port backup test. 4. Support Ethernet port backup status displayed on home screen in fiber converter mode. 5. Support frame rate readback in NovaLCT. 6. Support partial or overall settings for the mosaic backup mode. 7. Support OPT Loop mode. 8. Support OPT source cropping. 9. Support mode selection for OPT device. [Improvements] 1. Optimized the menu for factory reset. 2. Implemented an automatic re-identification measure for input sources to address the occasional issue where the input source not being identified upon power-up for the NovaPro UHD Jr and its front and back-end devices. 3. Optimized the Mapping function. (Provided the receiving card in use supports the Mapping function.) [Changes] None [Bug Fixes] 1. Fixed the problem that the screen will become blurred or go black transiently when the primary input source/Ethernet port/OPT port is switched to the backup. 2. Fixed the problem that the input source cannot be synchronized automatically after the device is restarted. 3. Fixed the problem that the output frame rate is not saved after power failure. [Notes] 1. When connecting an OPT input source to the primary NovaPro UHD Jr, only mode I is supported, and you will need to rotate the knob to select it. The fiber converter connected to the NovaPro UHD Jr supports various models such as NovaPro UHD Jr, CVT10, VX1000, and more, but does not support models like MCTRL4K and CVT4K. 2. When connecting a common input source to the primary NovaPro UHD Jr, you should select the OPT device mode based on the fiber converter model. Mode I supports models like NovaPro UHD Jr, CVT10, and VX1000, while mode II supports models like MCTRL4K, CVT4K. 3. The image on the screen might experience a momentary delay of 1-3 frames when switching the primary input source to the backup 4. Support frame rate readback in NovaLCT V5.4.8.CTM0904. The output frame rates of 56Hz and 70Hz cannot be read back. 5. When the device version is updated to V1.9.0.0 or downgraded to the previous version, you will need to reset the device to its factory settings. If you are using NovaLCT version V5.4.8.CTM0904, the device will be reset automatically (a pop-up window will be displayed before update). For any other versions of NovaLCT, please remember to reset the device manually. *****************************************2023.08.21 NovaPro UHD Jr V1.8.0.0.STD********************************************************************** [Supporting Software Version] V-Can V3.7.0 Beta or later NovaLCT V5.2.2 or later [New Features] 1. Support the OPT input (OPT 1 and 2). [Improvements] [Changes] [Bug Fixes] [Notes] 1. If the OPT source is used as the sync source, the device experiences issues such as no output, unrecognized source, and abnormal self-test after the quick screen configuration. These issues can be resolved by reconfiguring the screen. *****************************************2023.06.28 NovaPro UHD Jr V1.6.2.0.STD********************************************************************** [Supporting Software Version] V-Can V3.7.0 Beta or later NovaLCT V5.2.2 or later [New Features] [Improvements] [Changes] [Bug Fixes] 1. Fixed the problem the device fails to boot after the restart due to 3D overloading. [Notes] *****************************************2022.09.15 NovaPro UHD Jr V1.6.1.0.STD********************************************************************** [Supporting Software Version] V-Can V3.7.0.S2.T3 or later NovaLCT V5.2.2 or later [New Features] 1. Support the OSD function. [Improvements] [Changes] [Bug Fixes] 1. Fixed the problem of update failure on the Web page. [Notes] Currently, you need to use NovaLCT or V-Can to update the device to this version. You can perform the device update later on the Web page. *****************************************2022.06.14 NovaPro UHD Jr V1.5.1.0.STD********************************************************************** [Supporting Software Version] V-Can V3.6.0, V-Can V3.5.0 NovaLCT V5.2.2 or later [New Features] 1. The HDMI connector supports YUV420 color space. [Improvements] [Changes] 1. Optimized the display of Self-Test function in the Advanced Functions menu. [Bug Fixes] 1. After powered off and then powered on, the screen has no output or the screen connection parameters are lost occasionally. 2. Non-standard HDMI sources cannot be recognized occasionally. After they are disconnected and then connected, they can be recognized. 3. Fail to change the subnet mask on the web. 4. When a non-standard HDMI source is connected, the screen has color cast and becomes blurred occasionally. **************************************************************2021.7.6 NovaPro UHD Jr V1.2.2.0********************************************************************** [Supporting Software Version] NovaLCT V5.3.1 or later V-Can V3.6.0 or later SmartLCT V3.5.3 or later [New Features] 1. Support the 3D function and 1*1 mosaic layout (DVI Mosaic) to match V-Can. [Improvements] 1. Optimized the synchronization scheme. [Changes] 1. Released the HDCP function restriction on the HDMI 2.0 LOOP connector. [Bug Fixes] 1. Fixed the problem that the "VS_CNT" item in the test result is highlighted in red when the device functions well. 2. Fixed the problem of failing to set the device IP in V-Can under some circumstances. 3. Fixed the problem that the layer width is incorrect when you enable the input crop function and then change the layer input resolution from the maximum to the minimum in pixel-to-pixel mode. [Notes] None **************************************************************2020.9.30 NovaPro UHD Jr V1.2.1.0********************************************************************** [Supporting Software Version] NovaLCT V5.3.1 or later V-Can V3.5.1 or later (This version of V-Can is not released on the official website. Please contact our salesperson or technical support staff if needed.) SmartLCT V3.5.3 or later [New Features] 1. Support Web control. 2. Support turning on or off the HDCP function in the hidden menu. 3. Support working together with the HDR Master 4K. 4. Support turning on or off the Limited to Full function in the input settings menu, and switching between Full and Limited. 5. Support customizing DVI sources for DVI Mosaic. 6. Support customizing DVI sources for DVI Mosaic and Limited to Full functions when the device works with V-Can. [Improvements] 1. Optimized the self-test menu. The abnormal items will be highlighted in red. 2. Accelerated the calibration for the cascaded NovaPro UHD Jr units. 3. Removed the limitation that the width loaded by a single Ethernet port cannot exceed 512 pixels when low latency is enabled. 4. Changed the display of 576i and 480i on the device front panel screen to PAL (576i) and NTSC (480i). [Changes] None [Bug Fixes] 1. Fixed the problem that the parameters of extra-small area cropping from a high-resolution source cannot be saved. 2. Fixed the problem of abnormal display when the NovaPro UHD Jr works with V-Can for mosaic output. 3. Fixed the problem that a message prompts sometimes saying the capacity limit is exceeded when 3D function is enabled. 4. Fixed the problem that the last row of pixels is uncontrollable when HDR is enabled in some special screen configuration conditions. 5. Fixed the problem of failing to read the receiving card information when no layer is opened or the layer has no signal source. [Notes] None ************************************XXXX.XX.XX XXXX VX.X.X.X First Release ****************************************************************** [Supporting Software Version]